This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
cpm4030 [2024/01/19 11:23] – wrusman | cpm4030 [2024/01/19 12:27] – [Software] wrusman | ||
---|---|---|---|
Line 46: | Line 46: | ||
PCB gerber omzetten naar gcode : | PCB gerber omzetten naar gcode : | ||
- | [[https:// | + | [[https:// |
- | [[https:// | + | [[https:// |
- | [[http:// | + | [[http:// |
+ | [[https:// | ||
+ | [[https:// | ||
2d/3d tekening omzetten naar 2d / 2.5d / 3d gcode : | 2d/3d tekening omzetten naar 2d / 2.5d / 3d gcode : | ||
- | [[http:// | + | [[http:// |
- | [[https:// | + | [[https:// |
- | [[https:// | + | [[https:// |
+ | [[https:// | ||
+ | [[https:// | ||
+ | [[https:// | ||
+ | [[https:// | ||
+ | [[https:// | ||
CAM in bestaande tekensoftware : | CAM in bestaande tekensoftware : | ||
- | [[https:// | + | [[https:// |
- | [[https://www.freecadweb.org/|freecad]] | + | [[https://wiki.freecad.org/Path_Workbench|Path workbench in Freecad]] \\ |
+ | [[https:// | ||
+ | |||
+ | |||
+ | Grafische truukjes : | ||
+ | [[https:// | ||
+ | [[https:// | ||
+ | [[https:// | ||
problemen met arcs: | problemen met arcs: | ||
Line 69: | Line 85: | ||
Gcode streamers zijn bijna hetzelfde als 3D printer software die coördinaten naar de printer sturen vanaf de pc alleen zijn deze versies voornamelijk bedoeld voor Frezen of lasersnijden. | Gcode streamers zijn bijna hetzelfde als 3D printer software die coördinaten naar de printer sturen vanaf de pc alleen zijn deze versies voornamelijk bedoeld voor Frezen of lasersnijden. | ||
Niet elke software voor grbl werkt ook met FluidNC, dit is testen of uitzoeken. | Niet elke software voor grbl werkt ook met FluidNC, dit is testen of uitzoeken. | ||
+ | |||
+ | {{: | ||
+ | [[https:// | ||
{{: | {{: | ||
Line 81: | Line 100: | ||
{{: | {{: | ||
[[http:// | [[http:// | ||
- | |||
- | |||
Line 302: | Line 319: | ||
< | < | ||
G91 G21 ; (Relative position in mm.) | G91 G21 ; (Relative position in mm.) | ||
- | G38.2 Z-70 F100 ; | + | G38.2 Z-70 F100 ; |
- | G0 Z2 ; (back 2.mm) | + | G0 Z2 ; (back 2mm.) |
- | G38.2 Z-3 F30 ; (Search for the probe 3 mm; slower | + | G38.2 Z-2 F50 ; (Searching |
- | %wait% | + | G92 Z65 ; (Adjustment of the Z offset according to the thickness of the probe, 65 mm in this case) |
- | G20 | + | G0 Z75 ; (back 10mm.) |
- | %wait% | + | M0; (pause) |
- | G10 L20 P1 Z0.593 | + | |
- | %wait% | + | |
- | G0 Z.5 | + | |
- | G90 G21 | + | |
- | M0 | + | |
</ | </ | ||
+ | === "Ga naar positie x10 y10" | ||
+ | < | ||
+ | G90 G21; (Absolute position in mm.) | ||
+ | G0 X10 Y10; | ||
+ | </ |