This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revisionNext revisionBoth sides next revision | ||
cpm4030 [2024/01/19 11:23] – wrusman | cpm4030 [2024/01/31 11:08] – wrusman | ||
---|---|---|---|
Line 3: | Line 3: | ||
Dit is een CPM 4030, van het duitse bedrijf ISEL. | Dit is een CPM 4030, van het duitse bedrijf ISEL. | ||
- | {{: | + | {{: |
- | De bijgeleverde software | + | De bijgeleverde software |
+ | |||
+ | |||
+ | ===== Software ===== | ||
+ | === GCode Creeren / CAM === | ||
+ | |||
+ | PCB gerber omzetten naar gcode : \\ | ||
+ | [[https:// | ||
+ | [[https:// | ||
+ | [[http:// | ||
+ | [[https:// | ||
+ | [[https:// | ||
+ | |||
+ | |||
+ | 2d/3d tekening omzetten naar 2d / 2.5d / 3d gcode : \\ | ||
+ | [[http:// | ||
+ | [[https:// | ||
+ | [[https:// | ||
+ | [[https:// | ||
+ | [[https:// | ||
+ | [[https:// | ||
+ | [[https:// | ||
+ | [[https:// | ||
+ | |||
+ | CAM in bestaande tekensoftware : \\ | ||
+ | [[https:// | ||
+ | [[https:// | ||
+ | [[https:// | ||
+ | |||
+ | |||
+ | Grafische truukjes : \\ | ||
+ | [[https:// | ||
+ | [[https:// | ||
+ | [[https:// | ||
+ | |||
+ | |||
+ | problemen met arcs: \\ | ||
+ | [[https:// | ||
+ | |||
+ | === GCode Simulator : === | ||
+ | http:// | ||
+ | |||
+ | |||
+ | === GCode Streamers : === | ||
+ | Gcode streamers zijn bijna hetzelfde als 3D printer software die coördinaten naar de printer sturen vanaf de pc alleen zijn deze versies voornamelijk bedoeld voor Frezen of lasersnijden. | ||
+ | Niet elke software voor grbl werkt ook met FluidNC, dit is testen of uitzoeken. | ||
+ | |||
+ | {{: | ||
+ | [[https:// | ||
+ | |||
+ | {{: | ||
+ | [[https:// | ||
+ | |||
+ | {{: | ||
+ | [[https:// | ||
+ | |||
+ | {{: | ||
+ | [[https:// | ||
+ | |||
+ | {{: | ||
+ | [[http:// | ||
+ | |||
+ | ====== Electronica ====== | ||
+ | {{: | ||
Line 42: | Line 105: | ||
- | ===== Software | + | ====== Settings ====== |
- | === GCode Creeren / CAM === | + | ===== CAM en Sender instellingen |
+ | x: 380mm max 4000mm/min \\ | ||
+ | y: 300mm max 4000mm/min \\ | ||
+ | z: 200mm max 4000mm/min \\ | ||
- | PCB gerber omzetten naar gcode : | + | ===== FluidNC Settings ===== |
- | [[https:// | + | |
- | [[https:// | + | |
- | [[http:// | + | |
- | + | ||
- | 2d/3d tekening omzetten naar 2d / 2.5d / 3d gcode : | + | |
- | [[http:// | + | |
- | [[https:// | + | |
- | [[https:// | + | |
- | + | ||
- | CAM in bestaande tekensoftware : | + | |
- | [[https:// | + | |
- | [[https:// | + | |
- | + | ||
- | problemen met arcs: | + | |
- | [[https:// | + | |
- | + | ||
- | === GCode Simulator : === | + | |
- | http:// | + | |
- | + | ||
- | + | ||
- | === GCode Streamers : === | + | |
- | Gcode streamers zijn bijna hetzelfde als 3D printer software die coördinaten naar de printer sturen vanaf de pc alleen zijn deze versies voornamelijk bedoeld voor Frezen of lasersnijden. | + | |
- | Niet elke software voor grbl werkt ook met FluidNC, dit is testen of uitzoeken. | + | |
- | + | ||
- | {{: | + | |
- | [[https:// | + | |
- | + | ||
- | {{: | + | |
- | [[https:// | + | |
- | + | ||
- | {{: | + | |
- | [[https:// | + | |
- | + | ||
- | {{: | + | |
- | [[http:// | + | |
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | + | ||
- | ===== Settings ===== | + | |
=== config.yaml === | === config.yaml === | ||
< | < | ||
Line 302: | Line 327: | ||
< | < | ||
G91 G21 ; (Relative position in mm.) | G91 G21 ; (Relative position in mm.) | ||
- | G38.2 Z-70 F100 ; | + | G38.2 Z-70 F100 ; |
- | G0 Z2 ; (back 2.mm) | + | G0 Z2 ; (back 2mm.) |
- | G38.2 Z-3 F30 ; (Search for the probe 3 mm; slower | + | G38.2 Z-2 F50 ; (Searching |
- | %wait% | + | G92 Z65 ; (Adjustment of the Z offset according to the thickness of the probe, 65 mm in this case) |
- | G20 | + | G0 Z75 ; (back 10mm.) |
- | %wait% | + | M0; (pause) |
- | G10 L20 P1 Z0.593 | + | |
- | %wait% | + | |
- | G0 Z.5 | + | |
- | G90 G21 | + | |
- | M0 | + | |
</ | </ | ||
+ | === "Ga naar positie x10 y10" | ||
+ | < | ||
+ | G90 G21; (Absolute position in mm.) | ||
+ | G0 X10 Y10; | ||
+ | </ |