User Tools

Site Tools

Trace:
cpm4030

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
cpm4030 [2026/08/08 12:20] – wrusmancpm4030 [2026/08/08 12:43] (current) – wrusman
Line 19: Line 19:
  
 **Aluminium 6061** **Aluminium 6061**
-^Tool ^feedrate ^DOC mm ^WOC mm ^note^ +^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^ 
-|1 mm 2fl |200 |0.2 |0.15 |ramp, don't plunge| +|1 mm 2fl |200 |0.2 |0.15 |50 |2.5° |140 |ramp, don't plunge| 
-|* 2 mm 1fl |200 |0.5 |0.35 | | +|* 2 mm 1fl |200 |0.5 |0.35 |50 |2.5° |140 | | 
-|2 mm 2fl |300 |0.4 |0.3 | | +|2 mm 2fl |300 |0.4 |0.3 |75 |2.5° |210 | | 
-|3 mm 2fl |400 |0.6 |0.45 | | +|3 mm 2fl |400 |0.6 |0.45 |100 |2.5° |280 | | 
-|4 mm 2fl |500 |0.8 |0.6 | | +|4 mm 2fl |500 |0.8 |0.6 |125 |2.5° |350 | | 
-|* 4 mm 1fl |350 |1.0 |1.0|preferred — chip clearance| +|* 4 mm 1fl |350 |1.0 |1.0|88 |2.5° |245 |preferred — chip clearance| 
-|5 mm 2fl |600 |1.0 |1.0 | | +|5 mm 2fl |600 |1.0 |1.0 |150 |2.5° |420 | | 
-|6 mm 2fl |700 |1.20 |0.9 | |+|6 mm 2fl |700 |1.20 |0.9 |175 |2.5° |490 | |
  
 **Koper** **Koper**
-^Tool ^feedrate ^DOC mm ^WOC mm ^note^ +^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^ 
-|1 mm 2fl |160 |0.15 |0.15 | | +|1 mm 2fl |160 |0.15 |0.15 |32 |2° |112 | | 
-|* 2 mm 1fl |160 |0.35 |0.3 | | +|* 2 mm 1fl |160 |0.35 |0.3 |32 |2° |112 | | 
-|2 mm 2fl |240 |0.4 |0.3 | | +|2 mm 2fl |240 |0.4 |0.3 |48 |2° |168 | | 
-|3 mm 2fl |320 |0.6 |0.45 | | +|3 mm 2fl |320 |0.6 |0.45 |64 |2° |224 | | 
-|4 mm 2fl |400 |0.8 |0.6 | | +|4 mm 2fl |400 |0.8 |0.6 |80 |2° |280 | | 
-|* 4 mm 1fl |250 |0.7 |0.8|preferred — chip clearance| +|* 4 mm 1fl |250 |0.7 |0.8|50 |2° |175 |preferred — chip clearance| 
-|5 mm 2fl |480 |0.8 |0.75 | | +|5 mm 2fl |480 |0.8 |0.75 |96 |2° |336 | | 
-|6 mm 2fl |560 |1.20 |0.9 | |+|6 mm 2fl |560 |1.20 |0.9 |112 |2° |392 | |
  
 **Brons** **Brons**
-^Tool ^feedrate ^DOC mm ^WOC mm ^note^ +^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^ 
-|1 mm 2fl |160 |0.15 |0.15 | | +|1 mm 2fl |160 |0.15 |0.15 |32 |2° |112 | | 
-|* 2 mm 1fl |160 |0.35 |0.3 | | +|* 2 mm 1fl |160 |0.35 |0.3 |32 |2° |112 | | 
-|2 mm 2fl |240 |0.4 |0.3 | | +|2 mm 2fl |240 |0.4 |0.3 |48 |2° |168 | | 
-|3 mm 2fl |320 |0.6 |0.45 | | +|3 mm 2fl |320 |0.6 |0.45 |64 |2° |224 | | 
-|4 mm 2fl |400 |0.8 |0.6 | | +|4 mm 2fl |400 |0.8 |0.6 |80 |2° |280 | | 
-|* 4 mm 1fl |250 |0.7 |0.8|preferred — chip clearance| +|* 4 mm 1fl |250 |0.7 |0.8|50 |2° |175 |preferred — chip clearance| 
-|5 mm 2fl |480 |0.8 |0.75 | | +|5 mm 2fl |480 |0.8 |0.75 |96 |2° |336 | | 
-|6 mm 2fl |560 |1.20 |0.9 | |+|6 mm 2fl |560 |1.20 |0.9 |112 |2° |392 | |
  
 **Acryl / plexiglas** **Acryl / plexiglas**
-^Tool ^feedrate ^DOC mm ^WOC mm ^note^ +^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^ 
-|1 mm 2fl |600 |0.35 |0.35 | | +|1 mm 2fl |600 |0.35 |0.35 |180 |3.5° |480 | | 
-|* 2 mm 1fl |700 |0.9 |0.8 | | +|* 2 mm 1fl |700 |0.9 |0.8 |210 |3.5° |560 | | 
-|2 mm 2fl |1000 |0.7 |0.7 | | +|2 mm 2fl |1000 |0.7 |0.7 |300 |3.5° |800 | | 
-|3 mm 2fl |1200 |1.0 |1.0 | | +|3 mm 2fl |1200 |1.0 |1.0 |360 |3.5° |960 | | 
-|4 mm 2fl |1600 |1.4 |1.4 | | +|4 mm 2fl |1600 |1.4 |1.4 |480 |3.5° |1280 | | 
-|* 4 mm 1fl |1000 |2.0 |1.6|preferred — chip clearance| +|* 4 mm 1fl |1000 |2.0 |1.6|300 |3.5° |800 |preferred — chip clearance| 
-|5 mm 2fl |1800 |1.75 |1.75 | | +|5 mm 2fl |1800 |1.75 |1.75 |540 |3.5° |1440 | | 
-|6 mm 2fl |2000 |2.1 |2.1 | |+|6 mm 2fl |2000 |2.1 |2.1 |600 |3.5° |1600 | |
  
 **HDPE / POM / NYLON** **HDPE / POM / NYLON**
-^Tool ^feedrate ^DOC mm ^WOC mm ^note^ +^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^ 
-|1 mm 2fl |800 |0.45 |0.35 | | +|1 mm 2fl |800 |0.45 |0.35 |320 |5° |720 | | 
-|* 2 mm 1fl |850 |1.2 |0.8 | | +|* 2 mm 1fl |850 |1.2 |0.8 |340 |5° |765 | | 
-|2 mm 2fl |1200 |0.9 |0.7 | | +|2 mm 2fl |1200 |0.9 |0.7 |480 |5° |1080 | | 
-|3 mm 2fl |1600 |1.3 |1.0 | | +|3 mm 2fl |1600 |1.3 |1.0 |640 |5° |1440 | | 
-|4 mm 2fl |2000 |1.8 |1.4 | | +|4 mm 2fl |2000 |1.8 |1.4 |800 |5° |1800 | | 
-|* 4 mm 1fl |1200 |2.0 |1.6|preferred — chip clearance| +|* 4 mm 1fl |1200 |2.0 |1.6|480 |5° |1080 |preferred — chip clearance| 
-|5 mm 2fl |2400 |2.25 |1.75 | | +|5 mm 2fl |2400 |2.25 |1.75 |960 |5° |2160 | | 
-|6 mm 2fl |2800 |2.7 |2.1 | |+|6 mm 2fl |2800 |2.7 |2.1 |1120 |5° |2520 | |
  
 **Zacht hout / MDF / multiplex ** **Zacht hout / MDF / multiplex **
-^Tool ^feedrate ^DOC mm ^WOC mm ^note^ +^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^ 
-|1 mm 2fl |1000 |0.7 |0.45 | | +|1 mm 2fl |1000 |0.7 |0.45 |500 |9° |1000 | | 
-|2 mm 1fl |1100 |2.0 |1.0 | | +|2 mm 1fl |1100 |2.0 |1.0 |550 |9° |1100 | | 
-|2 mm 2fl |1600 |1.5 |0.9 | | +|2 mm 2fl |1600 |1.5 |0.9 |800 |9° |1600 | | 
-|3 mm 2fl |2000 |2.25 |1.35 | | +|3 mm 2fl |2000 |2.25 |1.35 |1000 |9° |2000 | | 
-|4 mm 2fl |2600 |3.0 |1.8 | | +|4 mm 2fl |2600 |3.0 |1.8 |1300 |9° |2600 | | 
-|4 mm 1fl |1500 |2.4 |1.6| | +|4 mm 1fl |1500 |2.4 |1.6|750 |9° |1500 | | 
-|5 mm 2fl |3000 |3.75 |2.25 | | +|5 mm 2fl |3000 |3.75 |2.25 |1500 |9° |3000 | | 
-|6 mm 2fl |3600 |4.50 |2.7 | |+|6 mm 2fl |3600 |4.50 |2.7 |1800 |9° |3600 | |
  
 **Hard hout ** **Hard hout **
-^Tool ^feedrate ^DOC mm ^WOC mm ^note^ +^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^ 
-|1 mm 2fl |800 |0.4 |0.35 | | +|1 mm 2fl |800 |0.4 |0.35 |320 |5.5° |720 | | 
-|2 mm 1fl |850 |1.0 |0.8 | | +|2 mm 1fl |850 |1.0 |0.8 |340 |5.5° |765 | | 
-|2 mm 2fl |1200 |0.8 |0.7 | | +|2 mm 2fl |1200 |0.8 |0.7 |480 |5.5° |1080 | | 
-|3 mm 2fl |1600 |1.2 |1.0 | | +|3 mm 2fl |1600 |1.2 |1.0 |640 |5.5° |1440 | | 
-|4 mm 2fl |2000 |1.6 |1.4 | | +|4 mm 2fl |2000 |1.6 |1.4 |800 |5.5° |1800 | | 
-|5 mm 2fl |2400 |2.0 |1.75 | | +|5 mm 2fl |2400 |2.0 |1.75 |960 |5.5° |2160 | | 
-|6 mm 2fl |2800 |2.4 |2.1 | |+|6 mm 2fl |2800 |2.4 |2.1 |1120 |5.5° |2520 | |
  
 ===== Software ===== ===== Software =====
cpm4030.txt · Last modified: by wrusman

Page Tools