Differences

This shows you the differences between two versions of the page.

--- cpm4030 [2025/08/28 10:03] – [Software] wrusman
+++ cpm4030 [2026/08/08 12:43] (current) – wrusman
@@ Line 7: / Line 7: @@
 De besturing en bijgeleverde software waren wat beperkt en verouderd, dus is hij omgebouwd naar FluidNC (grbl variant voor ESP32). http://wiki.fluidnc.com/
-====== Settings ======
+====== Freesjes ======
-===== CAM en Sender instellingen =====
-x: 380mm max  4000mm/min \\
-y: 300mm max  4000mm/min \\
-z: 200mm max  4000mm/min \\
+^  ^ Type ^ diameter  ^ Lengte ^ snijlengte ^ Doel ^ Link voor als hij stuk gaat  ^
+|{{:profiler:v-cutter.jpg?200|}}| 90 graden V-cutter | 6mm | 50mm| tip | Graveren / V-Carve | [[https://www.amazon.nl/gp/product/B07RZ4HS2J/ref=ppx_yo_dt_b_asin_title_o06_s00 | link]]|
+|{{:profiler:1snijder.jpg?200|}}| Frees 1-snijder (1 flute) | 4mm | 45mm | 22mm| uitfrezen van objecten of pockets | [[https://www.amazon.nl/dp/B07RHH5B5V?ref=ppx_yo2ov_dt_b_product_details | link]]|
+|{{:profiler:pcbfrees.jpg?200|}}| Frees 2-snijder (2 flute) | 0,6mm | ?mm | ?mm| Printplaten of fijn gaveerwerk | [[https://www.amazon.nl/dp/B09DCLQ5NL?ref=ppx_yo2ov_dt_b_product_details | link]]|
-===== Macro's =====
+====== Speeds en Feeds ======
-=== "Home All"  ===
+De spindel draait op 10000RPM, dat bepaalt de maximum en optimale snelheden.
-<code>
+Dit zijn richtlijnen, probeer het eerst met een stukje proefmateriaal
-$HZ ;$HX;G10 P0 L20 X0;$HY; G10 P0 L20 Y0;
-</code>
-=== "Probe Z" voor gebruik met de toolsetter (kan nog beter)===
+**Aluminium 6061**
-<code>
+^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^
-g90;g21;g38.2 z-70 f100;G92 z65;g1 z67;g38.2 z-10 f50;G92 z65;g0 z75;
+|1 mm 2fl |200 |0.2 |0.15 |50 |2.5° |140 |ramp, don't plunge|
-</code>
+|* 2 mm 1fl |200 |0.5 |0.35 |50 |2.5° |140 | |
+|2 mm 2fl |300 |0.4 |0.3 |75 |2.5° |210 | |
+|3 mm 2fl |400 |0.6 |0.45 |100 |2.5° |280 | |
+|4 mm 2fl |500 |0.8 |0.6 |125 |2.5° |350 | |
+|* 4 mm 1fl |350 |1.0 |1.0|88 |2.5° |245 |preferred — chip clearance|
+|5 mm 2fl |600 |1.0 |1.0 |150 |2.5° |420 | |
+|6 mm 2fl |700 |1.20 |0.9 |175 |2.5° |490 | |
-=== "Probe Z" voor gebruik met de toolsetter v2 (kan nog beter?)===
+**Koper**
-<code>
+^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^
-G21			; metric units
+|1 mm 2fl |160 |0.15 |0.15 |32 |2° |112 | |
-G91                  	; Relative Positioning
+|* 2 mm 1fl |160 |0.35 |0.3 |32 |2° |112 | |
-G38.2 Z-70 F100		; probe down with maximum 70mm and speed 100 mm/min
+|2 mm 2fl |240 |0.4 |0.3 |48 |2° |168 | |
-G10 L20 P1 Z65		; set G54 Z to 65mm at contact
+|3 mm 2fl |320 |0.6 |0.45 |64 |2° |224 | |
-G0 Z5			; retract 5mm
+|4 mm 2fl |400 |0.8 |0.6 |80 |2° |280 | |
-G38.2 Z-10 F50		; probe down with maximum 10mm and speed 50 mm/min
+|* 4 mm 1fl |250 |0.7 |0.8|50 |2° |175 |preferred — chip clearance|
-G10 L20 P1 Z65.3	; set G54 Z to 65mm at contact
+|5 mm 2fl |480 |0.8 |0.75 |96 |2° |336 | |
-G0 Z5			; retract 5mm
+|6 mm 2fl |560 |1.20 |0.9 |112 |2° |392 | |
-G90			; back to absolute
-</code>
-=== "Ga naar positie x10 y10"===
+**Brons**
-<code>
+^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^
-G90 G21; (Absolute position in mm.)
+|1 mm 2fl |160 |0.15 |0.15 |32 |2° |112 | |
-G0 X10 Y10;
+|* 2 mm 1fl |160 |0.35 |0.3 |32 |2° |112 | |
-</code>
+|2 mm 2fl |240 |0.4 |0.3 |48 |2° |168 | |
+|3 mm 2fl |320 |0.6 |0.45 |64 |2° |224 | |
+|4 mm 2fl |400 |0.8 |0.6 |80 |2° |280 | |
+|* 4 mm 1fl |250 |0.7 |0.8|50 |2° |175 |preferred — chip clearance|
+|5 mm 2fl |480 |0.8 |0.75 |96 |2° |336 | |
+|6 mm 2fl |560 |1.20 |0.9 |112 |2° |392 | |
+**Acryl / plexiglas**
+^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^
+|1 mm 2fl |600 |0.35 |0.35 |180 |3.5° |480 | |
+|* 2 mm 1fl |700 |0.9 |0.8 |210 |3.5° |560 | |
+|2 mm 2fl |1000 |0.7 |0.7 |300 |3.5° |800 | |
+|3 mm 2fl |1200 |1.0 |1.0 |360 |3.5° |960 | |
+|4 mm 2fl |1600 |1.4 |1.4 |480 |3.5° |1280 | |
+|* 4 mm 1fl |1000 |2.0 |1.6|300 |3.5° |800 |preferred — chip clearance|
+|5 mm 2fl |1800 |1.75 |1.75 |540 |3.5° |1440 | |
+|6 mm 2fl |2000 |2.1 |2.1 |600 |3.5° |1600 | |
+**HDPE / POM / NYLON**
+^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^
+|1 mm 2fl |800 |0.45 |0.35 |320 |5° |720 | |
+|* 2 mm 1fl |850 |1.2 |0.8 |340 |5° |765 | |
+|2 mm 2fl |1200 |0.9 |0.7 |480 |5° |1080 | |
+|3 mm 2fl |1600 |1.3 |1.0 |640 |5° |1440 | |
+|4 mm 2fl |2000 |1.8 |1.4 |800 |5° |1800 | |
+|* 4 mm 1fl |1200 |2.0 |1.6|480 |5° |1080 |preferred — chip clearance|
+|5 mm 2fl |2400 |2.25 |1.75 |960 |5° |2160 | |
+|6 mm 2fl |2800 |2.7 |2.1 |1120 |5° |2520 | |
+**Zacht hout / MDF / multiplex **
+^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^
+|1 mm 2fl |1000 |0.7 |0.45 |500 |9° |1000 | |
+|2 mm 1fl |1100 |2.0 |1.0 |550 |9° |1100 | |
+|2 mm 2fl |1600 |1.5 |0.9 |800 |9° |1600 | |
+|3 mm 2fl |2000 |2.25 |1.35 |1000 |9° |2000 | |
+|4 mm 2fl |2600 |3.0 |1.8 |1300 |9° |2600 | |
+|4 mm 1fl |1500 |2.4 |1.6|750 |9° |1500 | |
+|5 mm 2fl |3000 |3.75 |2.25 |1500 |9° |3000 | |
+|6 mm 2fl |3600 |4.50 |2.7 |1800 |9° |3600 | |
+**Hard hout **
+^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^
+|1 mm 2fl |800 |0.4 |0.35 |320 |5.5° |720 | |
+|2 mm 1fl |850 |1.0 |0.8 |340 |5.5° |765 | |
+|2 mm 2fl |1200 |0.8 |0.7 |480 |5.5° |1080 | |
+|3 mm 2fl |1600 |1.2 |1.0 |640 |5.5° |1440 | |
+|4 mm 2fl |2000 |1.6 |1.4 |800 |5.5° |1800 | |
+|5 mm 2fl |2400 |2.0 |1.75 |960 |5.5° |2160 | |
+|6 mm 2fl |2800 |2.4 |2.1 |1120 |5.5° |2520 | |
 ===== Software =====
-=== GCode Creeren / CAM ===
+=== CAM en Sender instellingen ===
-toptool : [[https://grid.space/kiri/|Kiri:Moto]] browser based CAM \\
+x: 380mm max  4000mm/min \\
-Settings : {{ :profiler:kiri-moto.zip |}}
+y: 300mm max  4000mm/min \\
+z: 200mm max  4000mm/min \\
+====== GCode Creeren / CAM ======
+toptool : [[https://grid.space/kiri/|Kiri:Moto]] browser based CAM &  {{ :profiler:kiri-moto.zip |presets}}
 van de makers van lightburn : [[https://docs.millmagesoftware.com/latest/AboutMillMage/|Millmage]]
@@ Line 60: / Line 114: @@
 d/3d tekening omzetten naar 2d / 2.5d / 3d gcode : \\
-[[http://www.cambam.info/|cambam]] \\
+[[http://www.cambam.info/|cambam]]  & {{ :profiler:cambam_plus_1.0_settings.zip |CamBam presets }} - via Tools -> browse system folder \\
 [[https://carbide3d.com/carbidecreate/|carbidecreate]] \\
 [[https://mecsoft.com/freemill/|freemill]] \\
@@ Line 73: / Line 127: @@
 [[https://wiki.freecad.org/Path_Workbench|Path workbench in Freecad]] \\
 [[https://forums.maslowcnc.com/t/generating-gcode-with-inkscape-instead-of-cam-software/12058|Inkscape]] \\
-Jens heeft een introductiefilmpje gemaakt over de CNC i.c.m. FreeCAD. {{youtube>Ix1RpRocqSg?}} \\
 Grafische truukjes : \\
+{{ ::halftoner.zip |Halftoner Applicatie Windows}} \\
+{{ :reactor.zip |Reactor Applicatie Windows}} \\
 [[https://halftonepro.com/app#|Halftone]] \\
 [[https://rasterbator.net/| Rasterbator]] \\
 [[https://picsvg.com | plaatjes naar svg]] \\
+eventuele problemen met arcs en nauwkeurigheid:  \\
-problemen met arcs:  \\
 [[https://softsolder.com/2020/03/18/grbl-error-33-arc-coordinates-vs-decimal-places/|G2/G3 error 33 uitleg en oplossing ]]
 === GCode Simulator : ===
 http://camotics.org/
 === GCode Streamers : ===
@@ Line 94: / Line 145: @@
 Niet elke software voor grbl werkt ook met FluidNC, dit is testen of uitzoeken.
-{{:profiler:gsender-main-screen-layout-850x441.png?400|}}
+[[https://resources.sienci.com/view/gs-installation/#download| GSender]] \\
-[[https://resources.sienci.com/view/gs-installation/#download| GSender]]
+[[https://github.com/winder/Universal-G-Code-Sender|Universal G-Code Sender (Java Cross-platform - ook voor mac!) ]] \\
+[[https://github.com/vlachoudis/bCNC|bCNC ]] \\
+[[https://github.com/Denvi/Candle|Candle ]] \\
+[[http://www.cambam.co.uk/forum/index.php?topic=6482|CamBam+ met plugin ]] \\
+van de makers van lightburn : [[https://docs.millmagesoftware.com/latest/AboutMillMage/|Millmage]] \\
-{{:profiler:sending_file_1.0.5.png?400|}}
+===== Macro's =====
-[[https://github.com/winder/Universal-G-Code-Sender|Universal G-Code Sender (Java Cross-platform - ook voor mac!) ]]
+=== "Home All"  ===
+<code>
+$HZ ;$HX;G10 P0 L20 X0;$HY; G10 P0 L20 Y0;
+</code>
-{{:profiler:bCNC.png?400|}}
+=== "Probe Z" voor gebruik met de toolsetter v2 (kan nog beter?)===
-[[https://github.com/vlachoudis/bCNC|bCNC ]]
+<code>
+G21			; metric units
+G91                  	; Relative Positioning
+G38.2 Z-70 F100		; probe down with maximum 70mm and speed 100 mm/min
+G10 L20 P1 Z65		; set G54 Z to 65mm at contact
+G0 Z5			; retract 5mm
+G38.2 Z-10 F50		; probe down with maximum 10mm and speed 50 mm/min
+G10 L20 P1 Z65.3	; set G54 Z to 65mm at contact
+G0 Z5			; retract 5mm
+G90			; back to absolute
+</code>
-{{:profiler:grblControl.png?400|}}
+=== oude "Probe Z" voor gebruik met de toolsetter (voor als de nieuwe niet goed werkt)===
-[[https://github.com/Denvi/Candle|Candle ]]
+<code>
+g90;g21;g38.2 z-70 f100;G92 z65;g1 z67;g38.2 z-10 f50;G92 z65;g0 z75;
+</code>
-{{:profiler:cambam.jpg?400|}}
+=== "Ga naar positie x10 y10"===
-[[http://www.cambam.co.uk/forum/index.php?topic=6482|CamBam+ met plugin ]]
+<code>
+G90 G21; (Absolute position in mm.)
+G0 X10 Y10;
+</code>
-====== Freesjes ======
-^  ^ Type ^ diameter  ^ Lengte ^ snijlengte ^ Doel ^ Link voor als hij stuk gaat  ^
-|{{:profiler:v-cutter.jpg?200|}}| 90 graden V-cutter | 6mm | 50mm| tip | Graveren / V-Carve | [[https://www.amazon.nl/gp/product/B07RZ4HS2J/ref=ppx_yo_dt_b_asin_title_o06_s00 | link]]|
-|{{:profiler:1snijder.jpg?200|}}| Frees 1-snijder | 4mm | 45mm | 22mm| uitfrezen van objecten of pockets | [[https://www.amazon.nl/dp/B07RHH5B5V?ref=ppx_yo2ov_dt_b_product_details | link]]|
-|{{:profiler:pcbfrees.jpg?200|}}| Frees 2-snijder | 0,6mm | ?mm | ?mm| Printplaten of fijn gaveerwerk | [[https://www.amazon.nl/dp/B09DCLQ5NL?ref=ppx_yo2ov_dt_b_product_details | link]]|
+Jens heeft een introductiefilmpje gemaakt over de CNC i.c.m. FreeCAD. {{youtube>Ix1RpRocqSg?}} \\
 ====== Electronica ======
@@ Line 358: / Line 426: @@
 </code>
+[[config.yaml|Experimental FluidNC config.yaml]]

User Tools

Site Tools

Differences

Page Tools