User Tools

Site Tools

Trace:
cpm4030

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
cpm4030 [2025/08/28 11:15] – wrusmancpm4030 [2026/08/08 12:43] (current) – wrusman
Line 6: Line 6:
  
 De besturing en bijgeleverde software waren wat beperkt en verouderd, dus is hij omgebouwd naar FluidNC (grbl variant voor ESP32). http://wiki.fluidnc.com/ De besturing en bijgeleverde software waren wat beperkt en verouderd, dus is hij omgebouwd naar FluidNC (grbl variant voor ESP32). http://wiki.fluidnc.com/
 +
 +====== Freesjes ======
 +
 +^  ^ Type ^ diameter  ^ Lengte ^ snijlengte ^ Doel ^ Link voor als hij stuk gaat  ^
 +|{{:profiler:v-cutter.jpg?200|}}| 90 graden V-cutter | 6mm | 50mm| tip | Graveren / V-Carve | [[https://www.amazon.nl/gp/product/B07RZ4HS2J/ref=ppx_yo_dt_b_asin_title_o06_s00 | link]]|
 +|{{:profiler:1snijder.jpg?200|}}| Frees 1-snijder (1 flute) | 4mm | 45mm | 22mm| uitfrezen van objecten of pockets | [[https://www.amazon.nl/dp/B07RHH5B5V?ref=ppx_yo2ov_dt_b_product_details | link]]|
 +|{{:profiler:pcbfrees.jpg?200|}}| Frees 2-snijder (2 flute) | 0,6mm | ?mm | ?mm| Printplaten of fijn gaveerwerk | [[https://www.amazon.nl/dp/B09DCLQ5NL?ref=ppx_yo2ov_dt_b_product_details | link]]|
 +
 +====== Speeds en Feeds ======
 +De spindel draait op 10000RPM, dat bepaalt de maximum en optimale snelheden.
 +Dit zijn richtlijnen, probeer het eerst met een stukje proefmateriaal
 +
 +**Aluminium 6061**
 +^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^
 +|1 mm 2fl |200 |0.2 |0.15 |50 |2.5° |140 |ramp, don't plunge|
 +|* 2 mm 1fl |200 |0.5 |0.35 |50 |2.5° |140 | |
 +|2 mm 2fl |300 |0.4 |0.3 |75 |2.5° |210 | |
 +|3 mm 2fl |400 |0.6 |0.45 |100 |2.5° |280 | |
 +|4 mm 2fl |500 |0.8 |0.6 |125 |2.5° |350 | |
 +|* 4 mm 1fl |350 |1.0 |1.0|88 |2.5° |245 |preferred — chip clearance|
 +|5 mm 2fl |600 |1.0 |1.0 |150 |2.5° |420 | |
 +|6 mm 2fl |700 |1.20 |0.9 |175 |2.5° |490 | |
 +
 +**Koper**
 +^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^
 +|1 mm 2fl |160 |0.15 |0.15 |32 |2° |112 | |
 +|* 2 mm 1fl |160 |0.35 |0.3 |32 |2° |112 | |
 +|2 mm 2fl |240 |0.4 |0.3 |48 |2° |168 | |
 +|3 mm 2fl |320 |0.6 |0.45 |64 |2° |224 | |
 +|4 mm 2fl |400 |0.8 |0.6 |80 |2° |280 | |
 +|* 4 mm 1fl |250 |0.7 |0.8|50 |2° |175 |preferred — chip clearance|
 +|5 mm 2fl |480 |0.8 |0.75 |96 |2° |336 | |
 +|6 mm 2fl |560 |1.20 |0.9 |112 |2° |392 | |
 +
 +**Brons**
 +^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^
 +|1 mm 2fl |160 |0.15 |0.15 |32 |2° |112 | |
 +|* 2 mm 1fl |160 |0.35 |0.3 |32 |2° |112 | |
 +|2 mm 2fl |240 |0.4 |0.3 |48 |2° |168 | |
 +|3 mm 2fl |320 |0.6 |0.45 |64 |2° |224 | |
 +|4 mm 2fl |400 |0.8 |0.6 |80 |2° |280 | |
 +|* 4 mm 1fl |250 |0.7 |0.8|50 |2° |175 |preferred — chip clearance|
 +|5 mm 2fl |480 |0.8 |0.75 |96 |2° |336 | |
 +|6 mm 2fl |560 |1.20 |0.9 |112 |2° |392 | |
 +
 +**Acryl / plexiglas**
 +^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^
 +|1 mm 2fl |600 |0.35 |0.35 |180 |3.5° |480 | |
 +|* 2 mm 1fl |700 |0.9 |0.8 |210 |3.5° |560 | |
 +|2 mm 2fl |1000 |0.7 |0.7 |300 |3.5° |800 | |
 +|3 mm 2fl |1200 |1.0 |1.0 |360 |3.5° |960 | |
 +|4 mm 2fl |1600 |1.4 |1.4 |480 |3.5° |1280 | |
 +|* 4 mm 1fl |1000 |2.0 |1.6|300 |3.5° |800 |preferred — chip clearance|
 +|5 mm 2fl |1800 |1.75 |1.75 |540 |3.5° |1440 | |
 +|6 mm 2fl |2000 |2.1 |2.1 |600 |3.5° |1600 | |
 +
 +**HDPE / POM / NYLON**
 +^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^
 +|1 mm 2fl |800 |0.45 |0.35 |320 |5° |720 | |
 +|* 2 mm 1fl |850 |1.2 |0.8 |340 |5° |765 | |
 +|2 mm 2fl |1200 |0.9 |0.7 |480 |5° |1080 | |
 +|3 mm 2fl |1600 |1.3 |1.0 |640 |5° |1440 | |
 +|4 mm 2fl |2000 |1.8 |1.4 |800 |5° |1800 | |
 +|* 4 mm 1fl |1200 |2.0 |1.6|480 |5° |1080 |preferred — chip clearance|
 +|5 mm 2fl |2400 |2.25 |1.75 |960 |5° |2160 | |
 +|6 mm 2fl |2800 |2.7 |2.1 |1120 |5° |2520 | |
 +
 +**Zacht hout / MDF / multiplex **
 +^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^
 +|1 mm 2fl |1000 |0.7 |0.45 |500 |9° |1000 | |
 +|2 mm 1fl |1100 |2.0 |1.0 |550 |9° |1100 | |
 +|2 mm 2fl |1600 |1.5 |0.9 |800 |9° |1600 | |
 +|3 mm 2fl |2000 |2.25 |1.35 |1000 |9° |2000 | |
 +|4 mm 2fl |2600 |3.0 |1.8 |1300 |9° |2600 | |
 +|4 mm 1fl |1500 |2.4 |1.6|750 |9° |1500 | |
 +|5 mm 2fl |3000 |3.75 |2.25 |1500 |9° |3000 | |
 +|6 mm 2fl |3600 |4.50 |2.7 |1800 |9° |3600 | |
 +
 +**Hard hout **
 +^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^
 +|1 mm 2fl |800 |0.4 |0.35 |320 |5.5° |720 | |
 +|2 mm 1fl |850 |1.0 |0.8 |340 |5.5° |765 | |
 +|2 mm 2fl |1200 |0.8 |0.7 |480 |5.5° |1080 | |
 +|3 mm 2fl |1600 |1.2 |1.0 |640 |5.5° |1440 | |
 +|4 mm 2fl |2000 |1.6 |1.4 |800 |5.5° |1800 | |
 +|5 mm 2fl |2400 |2.0 |1.75 |960 |5.5° |2160 | |
 +|6 mm 2fl |2800 |2.4 |2.1 |1120 |5.5° |2520 | |
  
 ===== Software ===== ===== Software =====
Line 13: Line 100:
 z: 200mm max  4000mm/min \\ z: 200mm max  4000mm/min \\
  
- +====== GCode Creeren / CAM ====== 
-=== GCode Creeren / CAM === +toptool : [[https://grid.space/kiri/|Kiri:Moto]] browser based CAM &  {{ :profiler:kiri-moto.zip |presets}}
-toptool : [[https://grid.space/kiri/|Kiri:Moto]] browser based CAM \\ +
-Settings : {{ :profiler:kiri-moto.zip |}}+
  
 van de makers van lightburn : [[https://docs.millmagesoftware.com/latest/AboutMillMage/|Millmage]] van de makers van lightburn : [[https://docs.millmagesoftware.com/latest/AboutMillMage/|Millmage]]
Line 29: Line 114:
  
 2d/3d tekening omzetten naar 2d / 2.5d / 3d gcode : \\ 2d/3d tekening omzetten naar 2d / 2.5d / 3d gcode : \\
-[[http://www.cambam.info/|cambam]] \\+[[http://www.cambam.info/|cambam]]  & {{ :profiler:cambam_plus_1.0_settings.zip |CamBam presets }} - via Tools -> browse system folder \\
 [[https://carbide3d.com/carbidecreate/|carbidecreate]] \\ [[https://carbide3d.com/carbidecreate/|carbidecreate]] \\
 [[https://mecsoft.com/freemill/|freemill]] \\ [[https://mecsoft.com/freemill/|freemill]] \\
Line 44: Line 129:
  
 Grafische truukjes : \\ Grafische truukjes : \\
 +{{ ::halftoner.zip |Halftoner Applicatie Windows}} \\
 +{{ :reactor.zip |Reactor Applicatie Windows}} \\
 [[https://halftonepro.com/app#|Halftone]] \\ [[https://halftonepro.com/app#|Halftone]] \\
 [[https://rasterbator.net/| Rasterbator]] \\ [[https://rasterbator.net/| Rasterbator]] \\
Line 94: Line 181:
 G0 X10 Y10; G0 X10 Y10;
 </code> </code>
- 
-====== Freesjes ====== 
- 
-^  ^ Type ^ diameter  ^ Lengte ^ snijlengte ^ Doel ^ Link voor als hij stuk gaat  ^ 
-|{{:profiler:v-cutter.jpg?200|}}| 90 graden V-cutter | 6mm | 50mm| tip | Graveren / V-Carve | [[https://www.amazon.nl/gp/product/B07RZ4HS2J/ref=ppx_yo_dt_b_asin_title_o06_s00 | link]]| 
-|{{:profiler:1snijder.jpg?200|}}| Frees 1-snijder | 4mm | 45mm | 22mm| uitfrezen van objecten of pockets | [[https://www.amazon.nl/dp/B07RHH5B5V?ref=ppx_yo2ov_dt_b_product_details | link]]| 
-|{{:profiler:pcbfrees.jpg?200|}}| Frees 2-snijder | 0,6mm | ?mm | ?mm| Printplaten of fijn gaveerwerk | [[https://www.amazon.nl/dp/B09DCLQ5NL?ref=ppx_yo2ov_dt_b_product_details | link]]| 
  
  
Line 346: Line 426:
 </code> </code>
  
 +[[config.yaml|Experimental FluidNC config.yaml]]
  
cpm4030.1756372536.txt.gz · Last modified: by wrusman

Page Tools