User Tools

Site Tools

Trace:
cpm4030

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
cpm4030 [2026/02/08 15:45] – wrusmancpm4030 [2026/06/25 11:38] (current) – wrusman
Line 6: Line 6:
  
 De besturing en bijgeleverde software waren wat beperkt en verouderd, dus is hij omgebouwd naar FluidNC (grbl variant voor ESP32). http://wiki.fluidnc.com/ De besturing en bijgeleverde software waren wat beperkt en verouderd, dus is hij omgebouwd naar FluidNC (grbl variant voor ESP32). http://wiki.fluidnc.com/
 +
 +====== Freesjes ======
 +
 +^  ^ Type ^ diameter  ^ Lengte ^ snijlengte ^ Doel ^ Link voor als hij stuk gaat  ^
 +|{{:profiler:v-cutter.jpg?200|}}| 90 graden V-cutter | 6mm | 50mm| tip | Graveren / V-Carve | [[https://www.amazon.nl/gp/product/B07RZ4HS2J/ref=ppx_yo_dt_b_asin_title_o06_s00 | link]]|
 +|{{:profiler:1snijder.jpg?200|}}| Frees 1-snijder | 4mm | 45mm | 22mm| uitfrezen van objecten of pockets | [[https://www.amazon.nl/dp/B07RHH5B5V?ref=ppx_yo2ov_dt_b_product_details | link]]|
 +|{{:profiler:pcbfrees.jpg?200|}}| Frees 2-snijder | 0,6mm | ?mm | ?mm| Printplaten of fijn gaveerwerk | [[https://www.amazon.nl/dp/B09DCLQ5NL?ref=ppx_yo2ov_dt_b_product_details | link]]|
 +
 +=== Speeds en Feeds ===
 +De spindel draait op 10000RPM, dat bepaalt de maximum en optimale snelheden.
 +Dit zijn richtlijnen, probeer het eerst met een stukje proefmateriaal
 +
 +**Aluminium 6061**
 +^Tool ^feed per tand ^feedrate mm/min ^stepover ^note^
 +|1 mm 2fl |0.006 |120 |0.10 |ramp, don't plunge|
 +|2 mm 2fl |0.012 |240 |0.30 | |
 +|3 mm 2fl |0.020 |400 |0.50 | |
 +|4 mm 1fl |0.045 |450 |0.6–1.0|preferred — chip clearance|
 +|6 mm 2fl |0.035 |700 |adaptive| Vc 189 high but Al tolerates it|
 +
 +**Koper**
 +^Tool ^feed per tand ^feedrate mm/min ^stepover ^note^
 +|2 mm 2fl |0.010 |200 |0.30 | |
 +|3 mm 2fl |0.016 |320 |0.30 | |
 +|4 mm 1fl |0.035 |350 |0.30 |preferred — chip clearance|
 +|6 mm 2fl |0.028 |560 |0.30 |Vc 189 = edge-buildup risk, watch it|
 +
 +**Brons**
 +^Tool ^feed per tand ^feedrate mm/min ^stepover ^
 +|2 mm 2fl |0.012 |240 |0.5×D|
 +|3 mm 2fl |0.020 |400 |0.5–0,9×D|
 +|4 mm 2fl |0.025 |500 |0.5–0,9×D|
 +|6 mm 2fl |0.030 |600 |adaptive for full depth|
 +
 +**Plastics**
 +^Tool ^feed per tand ^feedrate mm/min ^stepover ^
 +|2 mm 2fl |0.05 |1000 |up to 0,9×D|
 +|3 mm 2fl |0.07 |1400 |0,9×D|
 +|4 mm 1fl |0.10 |1000 |0,9×D preferred — chip clearance|
 +|6 mm 2fl |0.10 |2000 |0,9×D|
 +
 +**Hout**
 +^Tool ^feed per tand ^feedrate mm/min ^stepover ^
 +|3 mm 2fl |0.10 |2000 |0,9×D|
 +|4 mm 1fl |0.20 |2000 |0,9×D preferred — chip clearance|
 +|6 mm 2fl |0.15 |3000 |0,9×D|
  
 ===== Software ===== ===== Software =====
Line 13: Line 59:
 z: 200mm max  4000mm/min \\ z: 200mm max  4000mm/min \\
  
- +====== GCode Creeren / CAM ====== 
-=== GCode Creeren / CAM === +toptool : [[https://grid.space/kiri/|Kiri:Moto]] browser based CAM &  {{ :profiler:kiri-moto.zip |presets}}
-toptool : [[https://grid.space/kiri/|Kiri:Moto]] browser based CAM \\ +
-Settings : {{ :profiler:kiri-moto.zip |}}+
  
 van de makers van lightburn : [[https://docs.millmagesoftware.com/latest/AboutMillMage/|Millmage]] van de makers van lightburn : [[https://docs.millmagesoftware.com/latest/AboutMillMage/|Millmage]]
Line 29: Line 73:
  
 2d/3d tekening omzetten naar 2d / 2.5d / 3d gcode : \\ 2d/3d tekening omzetten naar 2d / 2.5d / 3d gcode : \\
-[[http://www.cambam.info/|cambam]] \\+[[http://www.cambam.info/|cambam]]  & {{ :profiler:cambam_plus_1.0_settings.zip |CamBam presets }} - via Tools -> browse system folder \\
 [[https://carbide3d.com/carbidecreate/|carbidecreate]] \\ [[https://carbide3d.com/carbidecreate/|carbidecreate]] \\
 [[https://mecsoft.com/freemill/|freemill]] \\ [[https://mecsoft.com/freemill/|freemill]] \\
Line 45: Line 89:
 Grafische truukjes : \\ Grafische truukjes : \\
 {{ ::halftoner.zip |Halftoner Applicatie Windows}} \\ {{ ::halftoner.zip |Halftoner Applicatie Windows}} \\
-{{ :reactor.zip |Reactor Applicatie Windows}}+{{ :reactor.zip |Reactor Applicatie Windows}} \\
 [[https://halftonepro.com/app#|Halftone]] \\ [[https://halftonepro.com/app#|Halftone]] \\
 [[https://rasterbator.net/| Rasterbator]] \\ [[https://rasterbator.net/| Rasterbator]] \\
Line 96: Line 140:
 G0 X10 Y10; G0 X10 Y10;
 </code> </code>
- 
-====== Freesjes ====== 
- 
-^  ^ Type ^ diameter  ^ Lengte ^ snijlengte ^ Doel ^ Link voor als hij stuk gaat  ^ 
-|{{:profiler:v-cutter.jpg?200|}}| 90 graden V-cutter | 6mm | 50mm| tip | Graveren / V-Carve | [[https://www.amazon.nl/gp/product/B07RZ4HS2J/ref=ppx_yo_dt_b_asin_title_o06_s00 | link]]| 
-|{{:profiler:1snijder.jpg?200|}}| Frees 1-snijder | 4mm | 45mm | 22mm| uitfrezen van objecten of pockets | [[https://www.amazon.nl/dp/B07RHH5B5V?ref=ppx_yo2ov_dt_b_product_details | link]]| 
-|{{:profiler:pcbfrees.jpg?200|}}| Frees 2-snijder | 0,6mm | ?mm | ?mm| Printplaten of fijn gaveerwerk | [[https://www.amazon.nl/dp/B09DCLQ5NL?ref=ppx_yo2ov_dt_b_product_details | link]]| 
  
  
cpm4030.1770561930.txt.gz · Last modified: by wrusman

Page Tools