User Tools

Site Tools

Trace:
cpm4030

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
cpm4030 [2026/06/25 11:24] – wrusmancpm4030 [2026/08/08 12:43] (current) – wrusman
Line 7: Line 7:
 De besturing en bijgeleverde software waren wat beperkt en verouderd, dus is hij omgebouwd naar FluidNC (grbl variant voor ESP32). http://wiki.fluidnc.com/ De besturing en bijgeleverde software waren wat beperkt en verouderd, dus is hij omgebouwd naar FluidNC (grbl variant voor ESP32). http://wiki.fluidnc.com/
  
-===== Software ===== +====== Freesjes ====== 
-=== CAM en Sender instellingen === + 
-x: 380mm max  4000mm/min \\ +^  ^ Type ^ diameter  ^ Lengte ^ snijlengte ^ Doel ^ Link voor als hij stuk gaat  ^ 
-y: 300mm max  4000mm/min \\ +|{{:profiler:v-cutter.jpg?200|}}| 90 graden V-cutter | 6mm | 50mm| tip | Graveren / V-Carve | [[https://www.amazon.nl/gp/product/B07RZ4HS2J/ref=ppx_yo_dt_b_asin_title_o06_s00 | link]]| 
-z: 200mm max  4000mm/min \\+|{{:profiler:1snijder.jpg?200|}}| Frees 1-snijder (1 flute) | 4mm | 45mm | 22mm| uitfrezen van objecten of pockets | [[https://www.amazon.nl/dp/B07RHH5B5V?ref=ppx_yo2ov_dt_b_product_details | link]]| 
 +|{{:profiler:pcbfrees.jpg?200|}}| Frees 2-snijder (2 flute) | 0,6mm | ?mm | ?mm| Printplaten of fijn gaveerwerk | [[https://www.amazon.nl/dp/B09DCLQ5NL?ref=ppx_yo2ov_dt_b_product_details | link]]|
  
-=== Speeds en Feeds ===+====== Speeds en Feeds ======
 De spindel draait op 10000RPM, dat bepaalt de maximum en optimale snelheden. De spindel draait op 10000RPM, dat bepaalt de maximum en optimale snelheden.
 Dit zijn richtlijnen, probeer het eerst met een stukje proefmateriaal Dit zijn richtlijnen, probeer het eerst met een stukje proefmateriaal
  
 **Aluminium 6061** **Aluminium 6061**
-^Tool ^feed per tand ^feedrate mm/min ^stepover ^note^ +^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^ 
-|1 mm 2fl |0.006 |120 |0.10 |ramp, don't plunge| +|1 mm 2fl |200 |0.2 |0.15 |50 |2.5° |140 |ramp, don't plunge| 
-|2 mm 2fl |0.012 |240 |0.30 | | +|* 2 mm 1fl |200 |0.5 |0.35 |50 |2.5° |140 | | 
-|3 mm 2fl |0.020 |400 |0.50 | | +|2 mm 2fl |300 |0.4 |0.3 |75 |2.5° |210 | | 
-|4 mm 1fl |0.045 |450 |0.6–1.0|best for alu| +|3 mm 2fl |400 |0.6 |0.45 |100 |2.5° |280 | | 
-|6 mm 2fl |0.035 |700 |adaptive| Vc 189 high but Al tolerates it|+|4 mm 2fl |500 |0.8 |0.6 |125 |2.5° |350 | | 
 +|* 4 mm 1fl |350 |1.0 |1.0|88 |2.5° |245 |preferred — chip clearance| 
 +|5 mm 2fl |600 |1.0 |1.0 |150 |2.5° |420 | | 
 +|6 mm 2fl |700 |1.20 |0.9 |175 |2.5° |490 | |
  
 **Koper** **Koper**
-^Tool ^feed per tand ^feedrate mm/min ^stepover ^note^ +^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^ 
-|2 mm 2fl |0.010 |200 |0.30 | | +|1 mm 2fl |160 |0.15 |0.15 |32 |2° |112 | | 
-|3 mm 2fl |0.016 |320 |0.30 | | +|* 2 mm 1fl |160 |0.35 |0.3 |32 |2° |112 | | 
-|4 mm 1fl |0.035 |350 |0.30 |preferred — chip clearance| +|2 mm 2fl |240 |0.4 |0.3 |48 |2° |168 | | 
-|6 mm 2fl |0.028 |560 |0.30 |Vc 189 = edge-buildup risk, watch it|+|3 mm 2fl |320 |0.6 |0.45 |64 |2° |224 | | 
 +|4 mm 2fl |400 |0.8 |0.6 |80 |2° |280 | | 
 +|* 4 mm 1fl |250 |0.7 |0.8|50 |2° |175 |preferred — chip clearance| 
 +|5 mm 2fl |480 |0.8 |0.75 |96 |2° |336 | | 
 +|6 mm 2fl |560 |1.20 |0.9 |112 |2° |392 | |
  
 +**Brons**
 +^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^
 +|1 mm 2fl |160 |0.15 |0.15 |32 |2° |112 | |
 +|* 2 mm 1fl |160 |0.35 |0.3 |32 |2° |112 | |
 +|2 mm 2fl |240 |0.4 |0.3 |48 |2° |168 | |
 +|3 mm 2fl |320 |0.6 |0.45 |64 |2° |224 | |
 +|4 mm 2fl |400 |0.8 |0.6 |80 |2° |280 | |
 +|* 4 mm 1fl |250 |0.7 |0.8|50 |2° |175 |preferred — chip clearance|
 +|5 mm 2fl |480 |0.8 |0.75 |96 |2° |336 | |
 +|6 mm 2fl |560 |1.20 |0.9 |112 |2° |392 | |
  
 +**Acryl / plexiglas**
 +^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^
 +|1 mm 2fl |600 |0.35 |0.35 |180 |3.5° |480 | |
 +|* 2 mm 1fl |700 |0.9 |0.8 |210 |3.5° |560 | |
 +|2 mm 2fl |1000 |0.7 |0.7 |300 |3.5° |800 | |
 +|3 mm 2fl |1200 |1.0 |1.0 |360 |3.5° |960 | |
 +|4 mm 2fl |1600 |1.4 |1.4 |480 |3.5° |1280 | |
 +|* 4 mm 1fl |1000 |2.0 |1.6|300 |3.5° |800 |preferred — chip clearance|
 +|5 mm 2fl |1800 |1.75 |1.75 |540 |3.5° |1440 | |
 +|6 mm 2fl |2000 |2.1 |2.1 |600 |3.5° |1600 | |
  
-=== GCode Creeren / CAM ===+**HDPE / POM / NYLON** 
 +^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^ 
 +|1 mm 2fl |800 |0.45 |0.35 |320 |5° |720 | | 
 +|* 2 mm 1fl |850 |1.2 |0.8 |340 |5° |765 | | 
 +|2 mm 2fl |1200 |0.9 |0.7 |480 |5° |1080 | | 
 +|3 mm 2fl |1600 |1.3 |1.0 |640 |5° |1440 | | 
 +|4 mm 2fl |2000 |1.8 |1.4 |800 |5° |1800 | | 
 +|* 4 mm 1fl |1200 |2.0 |1.6|480 |5° |1080 |preferred — chip clearance| 
 +|5 mm 2fl |2400 |2.25 |1.75 |960 |5° |2160 | | 
 +|6 mm 2fl |2800 |2.7 |2.1 |1120 |5° |2520 | | 
 + 
 +**Zacht hout / MDF / multiplex ** 
 +^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^ 
 +|1 mm 2fl |1000 |0.7 |0.45 |500 |9° |1000 | | 
 +|2 mm 1fl |1100 |2.0 |1.0 |550 |9° |1100 | | 
 +|2 mm 2fl |1600 |1.5 |0.9 |800 |9° |1600 | | 
 +|3 mm 2fl |2000 |2.25 |1.35 |1000 |9° |2000 | | 
 +|4 mm 2fl |2600 |3.0 |1.8 |1300 |9° |2600 | | 
 +|4 mm 1fl |1500 |2.4 |1.6|750 |9° |1500 | | 
 +|5 mm 2fl |3000 |3.75 |2.25 |1500 |9° |3000 | | 
 +|6 mm 2fl |3600 |4.50 |2.7 |1800 |9° |3600 | | 
 + 
 +**Hard hout ** 
 +^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^ 
 +|1 mm 2fl |800 |0.4 |0.35 |320 |5.5° |720 | | 
 +|2 mm 1fl |850 |1.0 |0.8 |340 |5.5° |765 | | 
 +|2 mm 2fl |1200 |0.8 |0.7 |480 |5.5° |1080 | | 
 +|3 mm 2fl |1600 |1.2 |1.0 |640 |5.5° |1440 | | 
 +|4 mm 2fl |2000 |1.6 |1.4 |800 |5.5° |1800 | | 
 +|5 mm 2fl |2400 |2.0 |1.75 |960 |5.5° |2160 | | 
 +|6 mm 2fl |2800 |2.4 |2.1 |1120 |5.5° |2520 | | 
 + 
 +===== Software ===== 
 +=== CAM en Sender instellingen === 
 +x: 380mm max  4000mm/min \\ 
 +y: 300mm max  4000mm/min \\ 
 +z: 200mm max  4000mm/min \\ 
 + 
 +====== GCode Creeren / CAM ======
 toptool : [[https://grid.space/kiri/|Kiri:Moto]] browser based CAM &  {{ :profiler:kiri-moto.zip |presets}} toptool : [[https://grid.space/kiri/|Kiri:Moto]] browser based CAM &  {{ :profiler:kiri-moto.zip |presets}}
  
Line 115: Line 181:
 G0 X10 Y10; G0 X10 Y10;
 </code> </code>
- 
-====== Freesjes ====== 
- 
-^  ^ Type ^ diameter  ^ Lengte ^ snijlengte ^ Doel ^ Link voor als hij stuk gaat  ^ 
-|{{:profiler:v-cutter.jpg?200|}}| 90 graden V-cutter | 6mm | 50mm| tip | Graveren / V-Carve | [[https://www.amazon.nl/gp/product/B07RZ4HS2J/ref=ppx_yo_dt_b_asin_title_o06_s00 | link]]| 
-|{{:profiler:1snijder.jpg?200|}}| Frees 1-snijder | 4mm | 45mm | 22mm| uitfrezen van objecten of pockets | [[https://www.amazon.nl/dp/B07RHH5B5V?ref=ppx_yo2ov_dt_b_product_details | link]]| 
-|{{:profiler:pcbfrees.jpg?200|}}| Frees 2-snijder | 0,6mm | ?mm | ?mm| Printplaten of fijn gaveerwerk | [[https://www.amazon.nl/dp/B09DCLQ5NL?ref=ppx_yo2ov_dt_b_product_details | link]]| 
  
  
Line 367: Line 426:
 </code> </code>
  
 +[[config.yaml|Experimental FluidNC config.yaml]]
  
cpm4030.1782379461.txt.gz · Last modified: by wrusman

Page Tools