User Tools

Site Tools

Trace:
cpm4030

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revisionPrevious revision
Next revision		Previous revision
cpm4030 [2026/06/25 11:38] – wrusmancpm4030 [2026/08/08 12:43] (current) – wrusman
Line 11: Line 11:
 ^  ^ Type ^ diameter  ^ Lengte ^ snijlengte ^ Doel ^ Link voor als hij stuk gaat  ^ ^  ^ Type ^ diameter  ^ Lengte ^ snijlengte ^ Doel ^ Link voor als hij stuk gaat  ^
 |{{:profiler:v-cutter.jpg?200|}}| 90 graden V-cutter | 6mm | 50mm| tip | Graveren / V-Carve | [[https://www.amazon.nl/gp/product/B07RZ4HS2J/ref=ppx_yo_dt_b_asin_title_o06_s00 | link]]| |{{:profiler:v-cutter.jpg?200|}}| 90 graden V-cutter | 6mm | 50mm| tip | Graveren / V-Carve | [[https://www.amazon.nl/gp/product/B07RZ4HS2J/ref=ppx_yo_dt_b_asin_title_o06_s00 | link]]|
-|{{:profiler:1snijder.jpg?200|}}| Frees 1-snijder | 4mm | 45mm | 22mm| uitfrezen van objecten of pockets | [[https://www.amazon.nl/dp/B07RHH5B5V?ref=ppx_yo2ov_dt_b_product_details | link]]| +|{{:profiler:1snijder.jpg?200|}}| Frees 1-snijder (1 flute) | 4mm | 45mm | 22mm| uitfrezen van objecten of pockets | [[https://www.amazon.nl/dp/B07RHH5B5V?ref=ppx_yo2ov_dt_b_product_details | link]]| 
-|{{:profiler:pcbfrees.jpg?200|}}| Frees 2-snijder | 0,6mm | ?mm | ?mm| Printplaten of fijn gaveerwerk | [[https://www.amazon.nl/dp/B09DCLQ5NL?ref=ppx_yo2ov_dt_b_product_details | link]]|+|{{:profiler:pcbfrees.jpg?200|}}| Frees 2-snijder (2 flute) | 0,6mm | ?mm | ?mm| Printplaten of fijn gaveerwerk | [[https://www.amazon.nl/dp/B09DCLQ5NL?ref=ppx_yo2ov_dt_b_product_details | link]]|
  
-=== Speeds en Feeds ===+====== Speeds en Feeds ======
 De spindel draait op 10000RPM, dat bepaalt de maximum en optimale snelheden. De spindel draait op 10000RPM, dat bepaalt de maximum en optimale snelheden.
 Dit zijn richtlijnen, probeer het eerst met een stukje proefmateriaal Dit zijn richtlijnen, probeer het eerst met een stukje proefmateriaal
  
 **Aluminium 6061** **Aluminium 6061**
-^Tool ^feed per tand ^feedrate mm/min ^stepover ^note^ +^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^ 
-|1 mm 2fl |0.006 |120 |0.10 |ramp, don't plunge| +|1 mm 2fl |200 |0.2 |0.15 |50 |2.5° |140 |ramp, don't plunge| 
-|2 mm 2fl |0.012 |240 |0.30 | | +|* 2 mm 1fl |200 |0.5 |0.35 |50 |2.5° |140 | | 
-|3 mm 2fl |0.020 |400 |0.50 | | +|2 mm 2fl |300 |0.4 |0.3 |75 |2.5° |210 | | 
-|4 mm 1fl |0.045 |450 |0.6–1.0|preferred — chip clearance| +|3 mm 2fl |400 |0.6 |0.45 |100 |2.5° |280 | | 
-|6 mm 2fl |0.035 |700 |adaptive| Vc 189 high but Al tolerates it|+|4 mm 2fl |500 |0.8 |0.6 |125 |2.5° |350 | | 
 +|* 4 mm 1fl |350 |1.0 |1.0|88 |2.5° |245 |preferred — chip clearance| 
 +|5 mm 2fl |600 |1.0 |1.0 |150 |2.5° |420 | | 
 +|6 mm 2fl |700 |1.20 |0.9 |175 |2.5° |490 | |
  
 **Koper** **Koper**
-^Tool ^feed per tand ^feedrate mm/min ^stepover ^note^ +^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^ 
-|2 mm 2fl |0.010 |200 |0.30 | | +|1 mm 2fl |160 |0.15 |0.15 |32 |2° |112 | | 
-|3 mm 2fl |0.016 |320 |0.30 | | +|* 2 mm 1fl |160 |0.35 |0.3 |32 |2° |112 | | 
-|4 mm 1fl |0.035 |350 |0.30 |preferred — chip clearance| +|2 mm 2fl |240 |0.4 |0.3 |48 |2° |168 | | 
-|6 mm 2fl |0.028 |560 |0.30 |Vc 189 = edge-buildup risk, watch it|+|3 mm 2fl |320 |0.6 |0.45 |64 |2° |224 | | 
 +|4 mm 2fl |400 |0.8 |0.6 |80 |2° |280 | | 
 +|* 4 mm 1fl |250 |0.7 |0.8|50 |2° |175 |preferred — chip clearance| 
 +|5 mm 2fl |480 |0.8 |0.75 |96 |2° |336 | | 
 +|6 mm 2fl |560 |1.20 |0.9 |112 |2° |392 | |
  
 **Brons** **Brons**
-^Tool ^feed per tand ^feedrate mm/min ^stepover ^ +^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^ 
-|2 mm 2fl |0.012 |240 |0.5×D| +|1 mm 2fl |160 |0.15 |0.15 |32 |2° |112 | | 
-|3 mm 2fl |0.020 |400 |0.5–0,9×D| +|* 2 mm 1fl |160 |0.35 |0.3 |32 |2° |112 | | 
-|4 mm 2fl |0.025 |500 |0.5–0,9×D| +|2 mm 2fl |240 |0.4 |0.3 |48 |2° |168 | | 
-|6 mm 2fl |0.030 |600 |adaptive for full depth|+|3 mm 2fl |320 |0.6 |0.45 |64 |2° |224 | | 
 +|4 mm 2fl |400 |0.8 |0.6 |80 |2° |280 | | 
 +|* 4 mm 1fl |250 |0.7 |0.8|50 |2° |175 |preferred — chip clearance| 
 +|5 mm 2fl |480 |0.8 |0.75 |96 |2° |336 | | 
 +|6 mm 2fl |560 |1.20 |0.9 |112 |2° |392 | |
  
-**Plastics** +**Acryl / plexiglas** 
-^Tool ^feed per tand ^feedrate mm/min ^stepover ^ +^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^ 
-|2 mm 2fl |0.05 |1000 |up to 0,9×D| +|1 mm 2fl |600 |0.35 |0.35 |180 |3.5° |480 | | 
-|3 mm 2fl |0.07 |1400 |0,9×D| +|* 2 mm 1fl |700 |0.9 |0.8 |210 |3.5° |560 | | 
-|4 mm 1fl |0.10 |1000 |0,9×D preferred — chip clearance| +|2 mm 2fl |1000 |0.7 |0.7 |300 |3.5° |800 | | 
-|6 mm 2fl |0.10 |2000 |0,9×D|+|3 mm 2fl |1200 |1.0 |1.0 |360 |3.5° |960 | | 
 +|4 mm 2fl |1600 |1.4 |1.4 |480 |3.5° |1280 | | 
 +|* 4 mm 1fl |1000 |2.0 |1.6|300 |3.5° |800 |preferred — chip clearance| 
 +|5 mm 2fl |1800 |1.75 |1.75 |540 |3.5° |1440 | | 
 +|6 mm 2fl |2000 |2.1 |2.1 |600 |3.5° |1600 | |
  
-**Hout** +**HDPE / POM / NYLON** 
-^Tool ^feed per tand ^feedrate mm/min ^stepover ^ +^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^ 
-|3 mm 2fl |0.10 |2000 |0,9×D| +|1 mm 2fl |800 |0.45 |0.35 |320 |5° |720 | | 
-|4 mm 1fl |0.20 |2000 |0,9×D preferred — chip clearance| +|* 2 mm 1fl |850 |1.2 |0.8 |340 |5° |765 | | 
-|6 mm 2fl |0.15 |3000 |0,9×D|+|2 mm 2fl |1200 |0.9 |0.7 |480 |5° |1080 | | 
 +|3 mm 2fl |1600 |1.3 |1.0 |640 |5° |1440 | | 
 +|4 mm 2fl |2000 |1.8 |1.4 |800 |5° |1800 | | 
 +|* 4 mm 1fl |1200 |2.0 |1.6|480 |5° |1080 |preferred — chip clearance| 
 +|5 mm 2fl |2400 |2.25 |1.75 |960 |5° |2160 | | 
 +|6 mm 2fl |2800 |2.7 |2.1 |1120 |5° |2520 | | 
 + 
 +**Zacht hout / MDF / multiplex ** 
 +^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^ 
 +|1 mm 2fl |1000 |0.7 |0.45 |500 |9° |1000 | | 
 +|2 mm 1fl |1100 |2.0 |1.0 |550 |9° |1100 | | 
 +|2 mm 2fl |1600 |1.5 |0.9 |800 |9° |1600 | | 
 +|3 mm 2fl |2000 |2.25 |1.35 |1000 |9° |2000 | | 
 +|4 mm 2fl |2600 |3.0 |1.8 |1300 |9° |2600 | | 
 +|4 mm 1fl |1500 |2.4 |1.6|750 |9° |1500 | | 
 +|5 mm 2fl |3000 |3.75 |2.25 |1500 |9° |3000 | | 
 +|6 mm 2fl |3600 |4.50 |2.7 |1800 |9° |3600 | | 
 + 
 +**Hard hout ** 
 +^Tool ^feedrate ^DOC mm ^WOC mm ^plunge ^ramp angle ^ramp feed ^note^ 
 +|1 mm 2fl |800 |0.4 |0.35 |320 |5.5° |720 | | 
 +|2 mm 1fl |850 |1.0 |0.8 |340 |5.5° |765 | | 
 +|2 mm 2fl |1200 |0.8 |0.7 |480 |5.5° |1080 | | 
 +|3 mm 2fl |1600 |1.2 |1.0 |640 |5.5° |1440 | | 
 +|4 mm 2fl |2000 |1.6 |1.4 |800 |5.5° |1800 | | 
 +|5 mm 2fl |2400 |2.0 |1.75 |960 |5.5° |2160 | | 
 +|6 mm 2fl |2800 |2.4 |2.1 |1120 |5.5° |2520 | |
  
 ===== Software ===== ===== Software =====
Line 385: Line 426:
 </code> </code>
  
 +[[config.yaml|Experimental FluidNC config.yaml]]
  
cpm4030.1782380307.txt.gz · Last modified: by wrusman

Page Tools