This is an old revision of the document!

Beschikbare Freesjes

Type	diameter	Lengte	snijlengte	Doel	Link voor als hij stuk gaat
90 graden V-cutter	6mm	50mm	tip	Graveren / V-Carve	link
End mill 1-snijder (1 flute)	4mm	45mm	22mm	uitfrezen van objecten of pockets	link
End mill 2-snijder (2 flute)	0,6mm	?mm	?mm	Printplaten of fijn gaveerwerk	link
End mill 2-snijder (2 flute)	2mm	?mm	12mm	countour frezen
End mill 2-snijder (2 flute)	4mm	?mm	12mm	countour frezen
End mill 2-snijder xl (2 flute)	4mm	?mm	20mm	countour frezen
End mill 2-snijder (2 flute)	5mm	?mm	20mm	countour frezen
End mill 2-snijder (2 flute)	6mm	?mm	20mm	countour frezen
Ballnose mill 2-snijder (2 flute)	2mm	?mm	12mm	3d frezen
Ballnose mill 2-snijder (2 flute)	4mm	?mm	12mm	3d frezen
Ballnose mill 2-snijder xl (2 flute)	4mm	?mm	20mm	3d frezen
Ballnose mill 2-snijder (2 flute)	5mm	?mm	20mm	3d frezen
Ballnose mill 2-snijder (2 flute)	6mm	?mm	20mm	3d frezen

Speeds en Feeds

De spindel draait op 10000RPM, dat bepaalt de maximum en optimale snelheden. Dit zijn richtlijnen, probeer het eerst met een stukje proefmateriaal

Aluminium 6061

Tool	feedrate	DOC mm	WOC mm	plunge	ramp angle	ramp feed	note
1 mm 2fl	200	0.1 - 0.2	0.15	50	2.5°	140	ramp, don't plunge
* 2 mm 1fl	200	0.3 - 0.5	0.35	50	2.5°	140
2 mm 2fl	300	0.2 - 0.4	0.3	75	2.5°	210
3 mm 2fl	400	0.4 - 0.6	0.45	100	2.5°	280
4 mm 2fl	500	0.5 - 0.8	0.6	125	2.5°	350
* 4 mm 1fl	500	0.5 - 0.8	0.6	88	2.5°	245	preferred — chip clearance
5 mm 2fl	600	0.8 - 1.0	1.0	150	2.5°	420
6 mm 2fl	700	0.9 - 1.20	0.9	175	2.5°	490

Koper

Tool	feedrate	DOC mm	WOC mm	plunge	ramp angle	ramp feed	note
1 mm 2fl	160	0.15	0.15	32	2°	112
* 2 mm 1fl	160	0.35	0.3	32	2°	112
2 mm 2fl	240	0.4	0.3	48	2°	168
3 mm 2fl	320	0.6	0.45	64	2°	224
4 mm 2fl	400	0.8	0.6	80	2°	280
* 4 mm 1fl	250	0.7	0.8	50	2°	175	preferred — chip clearance
5 mm 2fl	480	0.8	0.75	96	2°	336
6 mm 2fl	560	1.20	0.9	112	2°	392

Brons

Tool	feedrate	DOC mm	WOC mm	plunge	ramp angle	ramp feed	note
1 mm 2fl	160	0.15	0.15	32	2°	112
* 2 mm 1fl	160	0.35	0.3	32	2°	112
2 mm 2fl	240	0.4	0.3	48	2°	168
3 mm 2fl	320	0.6	0.45	64	2°	224
4 mm 2fl	400	0.8	0.6	80	2°	280
* 4 mm 1fl	250	0.7	0.8	50	2°	175	preferred — chip clearance
5 mm 2fl	480	0.8	0.75	96	2°	336
6 mm 2fl	560	1.20	0.9	112	2°	392

Acryl / plexiglas

Tool	feedrate	DOC mm	WOC mm	plunge	ramp angle	ramp feed	note
1 mm 2fl	600	0.35	0.35	180	3.5°	480
* 2 mm 1fl	700	0.9	0.8	210	3.5°	560
2 mm 2fl	1000	0.7	0.7	300	3.5°	800
3 mm 2fl	1200	1.0	1.0	360	3.5°	960
4 mm 2fl	1600	1.4	1.4	480	3.5°	1280
* 4 mm 1fl	1000	2.0	1.6	300	3.5°	800	preferred — chip clearance
5 mm 2fl	1800	1.75	1.75	540	3.5°	1440
6 mm 2fl	2000	2.1	2.1	600	3.5°	1600

HDPE / POM / NYLON

Tool	feedrate	DOC mm	WOC mm	plunge	ramp angle	ramp feed	note
1 mm 2fl	800	0.45	0.35	320	5°	720
* 2 mm 1fl	850	1.2	0.8	340	5°	765
2 mm 2fl	1200	0.9	0.7	480	5°	1080
3 mm 2fl	1600	1.3	1.0	640	5°	1440
4 mm 2fl	2000	1.8	1.4	800	5°	1800
* 4 mm 1fl	1200	2.0	1.6	480	5°	1080	preferred — chip clearance
5 mm 2fl	2400	2.25	1.75	960	5°	2160
6 mm 2fl	2800	2.7	2.1	1120	5°	2520

Zacht hout / MDF / multiplex

Tool	feedrate	DOC mm	WOC mm	plunge	ramp angle	ramp feed
1 mm 2fl	1000	0.7	0.45	500	9°	1000
2 mm 1fl	1100	2.0	1.0	550	9°	1100
2 mm 2fl	1600	1.5	0.9	800	9°	1600
3 mm 2fl	2000	2.25	1.35	1000	9°	2000
4 mm 2fl	2600	3.0	1.8	1300	9°	2600
4 mm 1fl	1500	2.4	1.6	750	9°	1500
5 mm 2fl	3000	3.75	2.25	1500	9°	3000
6 mm 2fl	3600	4.50	2.7	1800	9°	3600

Hard hout

Tool	feedrate	DOC mm	WOC mm	plunge	ramp angle	ramp feed
1 mm 2fl	800	0.4	0.35	320	5.5°	720
2 mm 1fl	850	1.0	0.8	340	5.5°	765
2 mm 2fl	1200	0.8	0.7	480	5.5°	1080
3 mm 2fl	1600	1.2	1.0	640	5.5°	1440
4 mm 2fl	2000	1.6	1.4	800	5.5°	1800
5 mm 2fl	2400	2.0	1.75	960	5.5°	2160
6 mm 2fl	2800	2.4	2.1	1120	5.5°	2520